Home > Fax Error > Fax Error Codes Canon

Fax Error Codes Canon

Contents

Call the telephone provider if line conditions fail to improve. 291 292 The received fax could not be stored. Enable the remote diagnostics capability on the local machine, if available. ID If Department ID Management is set, the Department ID is printed. Mirrorless Cameras The power of DSLR in the body of a compact. have a peek at these guys

Confirm that the remote caller is a fax machine and not a voice call. Reset the ink detection waste ink pad capacity to 0, in the service mode. The call waiting service can cause this error. Solution: Have the other party retransmit ##118 [ RX ] T1 timer over after reception of second sheet. this content

Canon Fax Error Code Ng

If necessary, ask error and thus an image memory overflow. A. crease the transmission level so that GI2 may be received correctly. Solution: Boost the transmission level so the other party can receive the protocol properly.

Cause: Abnormal protocol. Page 41 Chapter1: User Error Codes #055 [ TX ] The other party does not have an MDC (Multi Device Controller) function [exclusively for GP55] Cause Remedy • Although an attempt Solution: Have the other party boost the transmission level to receive data properly. Canon Fax Error Code 104 Remedy Check the destination setting. #803 Cause 1 The connection was interrupted due to reasons on the recipient's side before all of the pages could be sent.

Page 132 Chapter 2: Service Error Codes ##342 [ TX/RX ] Ink absorber for cleaning has become full Cause Remedy • The ink absorber for cleaning has become • Turn off Wait until the transmission/reception is complete. Contact your telephone company and the manufacturer of your terminal adapter or telephone adapter. great post to read Press [Function Settings] → [Send] → [Fax Settings]. 3.

A. Canon Result Ng C. Solution: Power cycle the machine. Cause: Defective internal unit.

Canon Fax Machine Error Codes

If this is the case, ask the sender to retry a normal transmission from the remote machine. over here Solution: Record the protocol on DAT tape and then request the Canon Technical center to analyze the information. ##110 [ TX ] Detect PIS during picture transmission. Canon Fax Error Code Ng Cause: Abnormal protocol. Canon Error #099 Solution: Replace the SCNT PWB. ##266 [ TX / RX ] Internal signal error.

Page 149 • Record the protocol on a DAT or MD, and have it analyzed by the local Canon office and/or Technical Center. 1. More about the author Cause: The user telephone number is not registered; (if receiver is Ricoh 3000L). B. Page 116 Chapter 2: Service Error Codes ##306 [ TX ] System error has occurred between the modem and the main CPU Cause Remedy • An internal unit is faulty (i.e., Canon Fax Error #099

Page 209 Chapter 2: Service Error Codes ##1042 [ TX/RX ] Switching equipment congestion Cause Remedy • Cause number #42 (Switching equipment • Wait a while, and start a communication congestion) Solution: Replace the modem or modem attached circuit board. Confirm that the remote fax machine is ready to receive a document, and then try sending the fax again. 313 A busy signal was detected each time the local machine attempted check my blog Select a slower reception speed.

Page 219 Chapter 2: Service Error Codes ##1081 [ TX/RX ] Invalid call reference value Cause Remedy • Cause number #81 (In no consumer canon.svg Products Services & Apps Get Inspired G3 Fax Solution: Record the protocol on DAT tape and then request the Canon Technical center to analyze the information. ##718 [ TX ] Decode error by other party during ARQ transmission. No solution is available.

Procedure Signal: It is a generic term for a tonal signal and a binary signal.

For descriptions unique to a specific model, refer also to its Service Manual. CANON INC. have it analyzed by the local Canon office and/or Technical Center. 2-104... Reserved Communication Jobs Were Cleared. Solution: Replace the SCNT PWB, and register a value for the absorption capacity, according to the quantity of absorbed ink in pad. ##342 [ TX / RX ] Cleaning absorption

Try the fax when telephone line conditions have improved. 440 441 442 443 444 An error occurred during transmission after one or more partial pages were sent. Remedy ^Ll • Provide echo remedy 1" - • Using a manual call, press the Start — button after hearing the 1 st DIS from the other party. •Transmit once again. Confirm that the local user really wants to attempt a poll reception. news A.

Solution: Boost the transmission level so that the other party can receive picture or EOL signals properly. The local machine held the remote machine during reception of a large or complex document due to lack of available memory. All graphics were produced with Adobe Illustrator 9.0J®. Connect Station CS100 Easy home storage for images and videos.

Note: if the capacity of the absorption pad is unclear, register a value corresponding to the quantity of absorbed ink in pad Solution: Replace the PCNT PWB, and register a