Home > Fax Error > Fax Error Codes Ng

Fax Error Codes Ng

Contents

Hello.NG means: Some or no pages sent.Check the paper feeder to see if the page is pulling through.Listen to see if the fax line "sounds"like it is working or if you Solution: Boost the transmission level so that the other party can receive DIS properly. Remedy2 Do not send the document to too many recipients at the same time. Remedy First, check the telephone line number for the server machine. (See [Set Line] in "Settings/Registration Table.") Then, set the correct telephone line number for the server machine in Remote Fax check my blog

Cause 2 The documents could not be sent because the recipient's machine was performing another task. A. G. Set Allow Fax Driver TX to 'On'. (See [Allow Fax Driver TX] in "Settings/Registration Table.") #025 Cause 1 A telephone line not connected to the Remote Fax server machine was specified http://support.brother.com/g/b/faqend.aspx?c=hk&lang=en&prod=mfc9330cdw_us_eu_as&faqid=faq00000209_014

Result Ng Canon

Solution: Boost the transmission level so the other party can receive CFR2 properly. B. A. It's simply "No Good", transmission is not completed, due to the receiving line is not available or busy, possible you do not have an active line, and you have plug the

Cause: Cannot receive picture signals properly due to poor line conditions. Tip: The max point reward for answering a question is 15. Note 1: These were to Fax Machines with encryptor devices and long distance...Avoid Call Backs. Canon Fax Ng #018 I apologise if the jargon is confusing, just try to go through the process one step at a time and you should be fine.

Cause: Defective internal unit; (RTC does not go on after RCVEND reception during T$ decoder). Fax Machine Poor Line Condition Out Of Memory Cause: Proper EOL signal at the start of the picture signal was not received due to poor line conditions. Solution: Replace the read end sensor. ##503 [ TX ] Fail MCF1 or PIS reception during G1 transmission. A.

Solution: Contact by phone. Fax Result Cont Cause: Abnormal protocol. Solution: Press Start button after confirming the first DIS from the other party during a manual call. Solution: Boost the transmission level so that the other party can receive the signals.

Fax Machine Poor Line Condition Out Of Memory

Remedy Store the necessary document in the Mail Box and the Fax/I-Fax Inbox again, and then try to send the link via e-mail. #754 Cause 1 The server is not functioning Remedy Re-enter the destination in the Address Book, and try sending again. Result Ng Canon Cause: Cannot receive signals properly due to poor line conditions. Fax Result Ng Poor Line Condition The activity report says NG.

Solution: Refer to Service Manual. ##307 [ TX / RX ] Bad communication mode. click site B. Mar 22, 2010 | Canon FAXPHONE L80 Laser 1 Answer How do I print a confiramtion page to make sure my Press Funktion and then report-activity reports will be displayed press Solution: Boost the transmission level so the other party can receive the phase signal properly. Canon Fax Machine Error Codes

DESTINATION ID The DESTINATION ID of the remote party is printed. Corporal: An expert that hasĀ over 10 points. Mar 22, 2010 | Canon FAXPHONE L80 Laser 2 Answers Getting Error TX Report: Result 'NG' - what does this mean??? news Solution: Lower the transmission start speed to 4800 bps.

Remedy Delete unnecessary documents to make more memory available. (See "Scan and Store," "Fax/I-Fax Inbox," and "Access Stored Files.") Cause 3 The scanned document cannot be stored because there are more Konica Minolta Ng Fax Error President: An expert whose answer gotĀ voted for 500 times. Solution: Clean the contact surface between the BJ cartridge and carriage with a soft clean cloth.

Solution: Retransmit. ##111 [ TX / RX ] Memory error.

Cause: The read end sensor is defective. B. Solution: Lower the transmission level to prevent reception of the transmitted CRF echo. ##265 [ TX / RX ] SCNT hardware signal error. Konica Minolta Fax Error Code Ng A.

Solution: Have the other party boost the transmission level so picture signals can be received properly. Cause: The operation of the UPI to control the G2 modem did not finish properly. Solution: Turn off the power and unplug the unit. More about the author Hello.NG means: Some or no pages sent.Check the paper feeder to see if the page is pulling through.Listen to see if the fax line "sounds"like it is working or if you

Solution: Turn the power OFF and then back ON. ##221 [ TX ] Actual-size recording crystal breakdown.